Magma Water Washable Photopolymer Resin Series 500g/ 1KG

New product

In Stock, Ship on next business day.




Add to wishlist

Data sheet

Weight 500g/1KG

More info

NOTE: It is water washable resin but not recommended to flush directly into the basin.

Magma Water Washable Photopolymer Resin

Magma H Line Water Washable Photopolymer Resin series is specifically formulated for 3D Printing where excess resin can be easily rinsed away with just water. It does not consist any volatile organic chemicals (VOC's). Suitable for most LCD/ DLP/ MSLA 3D Printer with 405nm wavelength. 

Suggested Exposure Time (Based on 405nm UV)

100 microns: 11 sec to 13 sec
50 microns: 7 sec to 10 sec
Bottom: 70 sec to 100 sec

100 microns: 5 sec to 7 sec
50 microns: 2 sec to 4 sec
Bottom: 10 sec to 15 sec

NOTE: The exposure time should be adjusted according to printer light energy, layer height and model structure.


  • No IPA, NO detergent, 100% clean by water
  • High Precision, excellent print details.
  • Low odor, less irritation
  • Slightly soluble in water
  • Not dangerous to environment
  • Non VOC
  • RoHS certificated
  • Compatible with most LCD/DLP/ MSLA printer with 405nm like FlashForge, Wanhao, Anycubic, Creality, Phrozen, Elegoo etc. 

Technical Data Specifications

Density (g/cm3):  1.05- 1.25
Viscosity (MPa·s): 100-350 
Hardness(Shore D): 80-85 D
Tensile strength (MPa)22.45
Elongation at break (%): 4-10
Flexural strength (MPa): 40-58
Flexural modulus (MPa): 1882-2385
 IZOD Impact Strength (j/m): 41- 48

Cleaning & Post Curing

Step 1 - Clean with flush water to a container and brush it gently with a soft brush, then dry it with cold air. Ensure it is fully dry.

Step 2-  Place the object in the UV Curing Chamber to cure. The curing time is proportional to the volume of the work piece and inversely proportional to the optical power of the curing chamber.


  • Shake well before use, and leave it for 30 minutes to eliminate air bubbles generated from the shaking process.
  • Magma Water Washable Photopolymer Resin is packed in opague UV safe bottle for ease of handling and safe storing.
  • Recommended storage temperature at 2-27°C (59-80°F) 
  • After use, it should be filtered and keep back in the opague UV bottle on time and placed in a dry and well ventilated place.
  • Store in cool and dry place, and avoid sunlight, recommended temperature at 25-30 degrees Celsius.

Important Safety Notices

  • Please wear mask and non-powdered nitrile gloves while handling with resin as the product is in a liquid state with slight odor.
  • Do not heat this product as photopolymer resins may produce vapours that may cause discomfort when exposed to high temperatures.
  • Keep the product out of children’s reach.
  • Avoid skin or eye contact with the uncured resin. If accidental contact occurs, please immediately rinse the affected area thoroughly using clean water.
  • Uncured resin in the tank may be harden if exposed to sunlight before disposal. Be aware when discarding uncured resin and do not dispose the uncured resin directly into the sink. 
  • After printing, please clean the uncured resin on the surface of the printed object using isoprophyl alcohol.
  • Dispose of waste in accordance with local environmental regulations.


Write a review

Magma Water Washable Photopolymer Resin Series 500g/ 1KG

Magma Water Washable Photopolymer Resin Series 500g/ 1KG