• -RM11.00
Magma Elastic Photopolymer Resin 500g - Transparent
search
  • Magma Elastic Photopolymer Resin 500g - Transparent
  • Magma Elastic Photopolymer Resin 500g - Transparent
  • Magma Elastic Photopolymer Resin 500g - Transparent
  • Magma Elastic Photopolymer Resin 500g - Transparent

Magma Elastic Photopolymer Resin 500g - Transparent

RM190.00
RM179.00 Save RM11.00
Ship On Next Business Day
mag-elastic-transparent-500g
Quantity
In Stock, Ship on next business day.


We Accept:

acceptpayment

Magma Elastic Photopolymer Resin 500g

Specially formulated to mimick rubber like material with fast rebound rates and high tearing resistance. It does not consist any volatile organic chemicals (VOC's) and EN 71-3 certified. Suitable for most LCD/ DLP/ MSLA 3D Printer with 355-405nm wavelength. 

Suggested Exposure Time (Based on 405nm UV)

(RGB )50 Micron: 6 to 12 sec / Base 80 to 100 Sec
(Mono) 50 Micron: 2 to 4 sec / Base 20 to 40 Sec

NOTE: The exposure time should be adjusted according to printer light energy, layer height and model structure.

Benefits:

- Fast rebound rate once being flexed

- Tear Resistance

- Elongation at break up to 200%

- Complied with EN 71-3 safety standard.

Technical Data Specifications

Density (g/cm3):  1.05- 1.25
Viscosity (MPa·s): 550-750 
Hardness(Shore A): 40-45
Tensile strength (MPa)0.66
Elongation at break (%): 135
 Wavelength: 355-405nm

Cleaning & Post Curing

Step 1 - Prepare two containers with IPA (> 95%), and place the object into the first container and gently shake it or gently brush it with a soft brush. After that soak it in the second container for about 1 minute

Step 2 -  Dry the object with cold air. Ensure it is fully dry.

Step 3-  Place the object in the UV Curing Chamber to cure. The curing time is proportional to the volume of the work piece and inversely proportional to the optical power of the curing chamber.

Storage 

  • Shake well before use, and leave it for 30 minutes to eliminate air bubbles generated from the shaking process.
  • Packed in opague UV safe bottle for ease of handling and safe storing.
  • Recommended storage temperature at 2-27°C (59-80°F) 
  • After use, it should be filtered and keep back in the opague UV bottle on time and placed in a dry and well ventilated place.
  • Store in cool and dry place, and avoid sunlight, recommended temperature at 25-30 degrees Celsius.

Important Safety Notices

  • Please wear mask and non-powdered nitrile gloves while handling with resin as the product is in a liquid state with slight odor.
  • Do not heat this product as photopolymer resins may produce vapours that may cause discomfort when exposed to high temperatures.
  • Keep the product out of children’s reach.
  • Avoid skin or eye contact with the uncured resin. If accidental contact occurs, please immediately rinse the affected area thoroughly using clean water.
  • Uncured resin in the tank may be harden if exposed to sunlight before disposal. Be aware when discarding uncured resin and do not dispose the uncured resin directly into the sink. 
  • After printing, please clean the uncured resin on the surface of the printed object using isoprophyl alcohol.
  • Dispose of waste in accordance with local environmental regulations.

Sold by 3D Gadgets Malaysia

mag-elastic-transparent-500g

Data sheet

Weight
500g
Comments (0)
No customer reviews for the moment.