Magma Castable Jewelry Resin

JWR-MGM-CTB-RESIN-1KG

New product

MAGMA JEWELRY CASTABLE RESIN

Environmentally-friendly resin, non-toxic and harmless, high precision, high strength or high flexibility, loss of wax, fast forming and so on.

More details

Ship within 14 to 21 working days

RM950.00

Add to wishlist

Data sheet

Weight 1KG
Material Castable Resin

More info

Magma Castable Jewelry Resin

Magma Castable Jewelry Resin is specifically formulated to be used in 3D printing which captures the finest detail, smooth and strong prints. Our resin has the properties of low shrinkage and low odour which makes it user- friendly. It is suitable for most DLP 3D Printer that utilizes UV light source or laser.

Suggested Exposure Time (Based on 405nm UV)

LCD/ MSLA
100 microns: 14 sec to 17 sec
50 microns: 10 sec to 13 sec
Bottom: 70 sec to 100 sec

DLP/ MSLA
100 microns: 5 sec to 7 sec
50 microns: 2 sec to 4 sec
Bottom: 15 sec to 30 sec

NOTE: The exposure time should be adjusted according to printer light energy, layer height and model structure.

Benefits

  •        High strength
  •        Fine details
  •        Smooth Finishing
  •        Low shrinkage
  •        Low odour resins
  •        Easy to cast 

Density (g/cm3):  1.05- 1.18
Viscosity (MPa·s): 100-450 
Hardness(Shore D): 64-68 D
Tensile strength (MPa)42-62
Elongation at break (%): 11-20
Flexural strength (MPa): 49-58
Flexural modulus (MPa): 1882-2385
 IZOD Impact Strength (j/m): 41- 49

Cleaning & Post Curing

Step 1 - Prepare two containers with IPA (> 95%), and place the object into the first container and gently shake it or gently brush it with a soft brush. After that soak it in the second container for about 1 minute

Step 2 -  Dry the object with cold air. Ensure it is fully dry.

Step 3-  Place the object in the UV Curing Chamber to cure. The curing time is proportional to the volume of the work piece and inversely proportional to the optical power of the curing chamber.

NOTE:

Do not soak in IPA for too long as it may crack and white spot may occur.

Do not use ultrasonic for cleaning, especially for casting resin.  

Storage 

  • Shake well before use, and leave it for 30 minutes to eliminate air bubbles generated from the shaking process.
  • Magma Resin is packed in opague UV safe bottle for ease of handling and safe storing.
  • Recommended storage temperature at 2-27°C (59-80°F) 
  • After use, it should be filtered and keep back in the opague UV bottle on time and placed in a dry and well ventilated place.
  • Store in cool and dry place, and avoid sunlight, recommended temperature at 25-30 degrees Celsius.

Important Safety Notices

  • Please wear mask and non-powdered nitrile gloves while handling with resin as the product is in a liquid state with slight odor.
  • Do not heat this product as photopolymer resins may produce vapours that may cause discomfort when exposed to high temperatures.
  • Keep the product out of children’s reach.
  • Avoid skin or eye contact with the uncured resin. If accidental contact occurs, please immediately rinse the affected area thoroughly using clean water.
  • Uncured resin in the tank may be harden if exposed to sunlight before disposal. Be aware when discarding uncured resin and do not dispose the uncured resin directly into the sink. 
  • After printing, please clean the uncured resin on the surface of the printed object using isoprophyl alcohol.
  • Dispose of waste in accordance with local environmental regulations.

Sold By 3D Gadgets Malaysia

Reviews

Write a review

Magma Castable Jewelry Resin

Magma Castable Jewelry Resin

MAGMA JEWELRY CASTABLE RESIN

Environmentally-friendly resin, non-toxic and harmless, high precision, high strength or high flexibility, loss of wax, fast forming and so on.